0.01mA resolution for DC current • Top class measurement 0.2% accuracy • Φ6mm clamp jaw easy to use in tight places • Measurement from 0.01mA to 120.0mA • Dual display with backlight shows both mA measurement and percent of 4-20 mA span • Spotlight for illuminating measurement point • Analog output terminal for recorder connection • Complies with IEC 61010-1 CAT.II 300V
3 channel inputs for the simultaneous recording of Leakage Current, Load Current and Voltage • Power Quality analysis(only on KEW 5020)(Power Quality:Reference voltage, Swell, Dip, Short power Interruptions) Large Capacity for storing 60,000 data points 60,000 data points can be recorded when 1ch is used, and when all the three channels are used, 20,000 data points per channel can be recorded Lowpass Filter will filter out the harmonics(Cutoff Frequency = Approx. 160Hz) LED flickers when the preset current / voltage value is exceeded CALL: Confirmation of recorded data • The following can be displayed: number of recorded data points, (max+ min+ peak) value for each channel complete with time/date information in the Normal recording mode. (Detected values (i.e. when values are outside preset limits ) can be displayed in other recording modes) • RECALL: The last 10 recorded data points including time/date can be recalled on the logger display
AC Voltmeter with linear, easy-to-read scales. • Auto discharge function; any charge stored in the circuit under test will be automatically discharged after testing. • Designed to meet IEC/EN 61010-1 CAT.III 600V, CAT.II 1000V • Color-coded scales for easy reading. • Back light function to facilitate working at dimly illuminated locations. • Test lead set with remote control switch. • Shoulder strap for hands free.
Digital Illuminometer • Model 5201 is a highly portable and compact digital illuminometer for measuring illuminance from 0.1 to 19,990 Lux, with auto range switching. • The digital display is held for a preset time (about 20 seconds) and, therefore, facilitates reading, recording and measuring in any direction.
Wide band 1mHz to 200kHz Chemical Impedance Analyzer for Testing Electrochemical Components and Materials, Batteries, and EDLC Hioki LCR and Impedance Analyzers range from 4Hz to 120MHz devices to suit a wide range of applications in the testing of electronic components. The IM3590 is an advanced component tester especially suited to electrochemical impedance measurements and includes a variety of graphing functions that are needed for battery and chemical material testing. This product is not supplied with measurement probes or test fixtures. Please select and purchase the measurement probe or test fixture options appropriate for your application separately. For an RS-232C connection: A crossover cable for interconnection can be used. You can use the RS-232C Cable 9637 without hardware flow control.
Leakage Current Testing According to IEC60990, IEC60335, and other Safety Standards To ensure the safe use of electrical products, electrical safety tests such as insulation resistance, withstand voltage, ground resistance, and leakage current must always be conducted. Hioki Leakage Current Testers comply with laws and standards regarding medical electrical equipment as well as non-medical electrical equipment, and can be used to measure leakage current in all types of electrical products from computers to medical equipment. The ST5541 provides support for standard-compliant networks (excluding medical-use electrical devices). Note: The photograph portrays the Japanese version of the product. Other countries’ versions of the product lack the outlet on the front panel. Note: For applications involving leak current measurement of medical-use electrical devices, use the ST5540.
DC, 0.5 Hz To 1 MHz, 6-Channel 3-Phase 4-Wire Power Meter with Direct and Clamp Sensor Input Hioki benchtop power meters and power analyzers are best in class power measuring instruments for measuring single to three-phase lines with a high degree of precision and accuracy. The 3193-10 is a 6-channel power meter for testing any type of circuit ranging from single-phase lines to three-phase four-wire lines. Based on the voltage, current, and active power measurements, the power meter calculates and displays reactive power, apparent power, power factor, phase angle, and efficiency. It also provides a wide range of measurement functions including frequency measurement function, peak measurement function, current integration, active power integration, analog outputs, monitor outputs, and optional harmonic analysis/flicker functionality. Note: Main unit 3193-10 cannot operate alone - please purchase an input unit Model 9600 to 9605 for factory installation prior to shipment. All subsequent input unit replacements or expansions must be conducted at HIOKI for an additional service charge.