You have 0 items in your cart.
GW Instek
Sub Categories
Stemming from the design and manufacture demands of electronic industries, GW Instek offers diverse...
In addition to provid complete electronic test and measurement instruments, GW Instek...
Category:
Programmable DC Electronic Load
Features : -Operating voltage (DC)：1.5V~150V-Operating Mode : C.C / C.V / C.R / C.P / CC+CV / CR+CV / CP+CV -Parallel Connection of Inputs for Higher Capacity (Max : 9,450W)-Support of High Slew Rate：Max 16A/us-Run Program Function（GO/NO GO Test）-Sequence Function for High Efficient Load Simulations-Commands are compatible with Kikusui PLZ-4W model.-Dynamic(Switching) Function：0.0166Hz ~20kHz-Soft Start Function：Off / On(1~200ms, Res：1ms)-Adjustable OCP / OVP / OPP / UVP Setting -Short Circuit Function-Timer function : Elapsed Time of load on -Cut Off Time(Auto Load Off Timer )：1s to 999h 59min 59s or Off -External Channel Control / Monitoring via Analog Control Connector-Setup Memories：100 sets-3.5 Inch TFT LCD Display-Multi Interface : USB 2.0 Device / Host , RS-232 , GPIB (Optional)
Category:
Discontinued Products
Features ※ 50000 Counts Display ※ Multi-Function ACV,DCV,ACA,DCA,R,C,Hz,Continuity Beeper,Diode Test,Max/Min,REL,Auto Hold,dBm※ Compare Function※ Dual Display Indicate ACV and Hz,DCV(ACV) and dBm※ DCV and ACV Ripple ※ Manual or Auto Ranging ※ 0.02% DCV Accuracy ※ ACV Measuring Frequency Up to 100kHz ※ 20A Current Range With High Energy Fuse Protection ※ Auto-Recall Settings upon Power ON ※ AC True RMS or AC + DC True RMS ※ RS-232C Interface ※ Option: GPIB Interface
Category:
Safety Testers
Features: ※ 500VA AC Test Capacity※ 240x64 Ice Blue Dot matrix LCD※ Sweep Function for DUT characteristic analysis※ Insulation resistance measurement up to 50GΩ(GPT-9903/9904)※ Manual/Auto Mode※ Function Key for quick selecation※ High intensity flash for caution & Status indication※ Safety INTERLOCK function※ Zero Crossing Turn-on Operation※ Controllable Ramp-up Time※ True RMS Current Measurement ※ High resolution: 1uA for measuring current, 2V for setting voltage※ PWM amplifier to enhance the power efficiency and reliable testing ※ Max. 100 memory block for test condition (step) setting. And each step can be named individually.※ Remote terminal on the front panel for “start” and “stop” control※ Rear panel output available※ Interface : RS-232C, USB device, Signal I/O and GPIB (optional)
Category:
LCR Fixtures
Features: * 4 Wire* SMD/Chip components support* Suitable for SMD Range: 0201 to 0805* For LCR-8000G, LCR-800 Series
Category:
Logic Analyzers
Features * 32/16 Input Channel * Time Analysis : Up to 200MHz Internal Sampling Rate * State Analysis : Up to 100MHz External Input Clock * Memory Depth : Up to 2Mbits/1Mbits (Half/Full Channels) * Enable Qualifier : High/Low Level Enable and Enable Delay Function * Signal Analyzer : I2C, RS-232C Protocol Analyzer and Signal Statistics * File Export : Signal Data, Operation Setting and Display Image * USB 2.0 Supported(1.1 Compatible)
Category:
Analog Function Generators
Features *Frequency Range 0.01Hz~15MHz *Maximum Frequency Resolution 10mHz *Dual Displays Indicate Frequency and Amplitude *Built-in 6 Digits Counter up to 150MHz/High Resolution *Output Waveforms Sine,Square,Triangle,Ramp,Pulse,Sweep,Gate or Burst *INT/EXT AM/FM Modulation *GCV Output for Synchronization *Output Overload Protection
Category:
Programmable Linear D.C. Power Supply
Features: Easy Operation with UP/DOWN Key High Resolution: 10mV, 1mA Over Voltage Protection, Over Current Protection by Hardware 100 Sets of Memory Self Test and Software Calibration Meets UL CSA IEC Safety Regulation Auto Step Running With Time Setting FRONT/REAR Output and Sense Switch Selectable IEEE-488.2 and SCPI Compatible Command set Labview Driver Software High Stability, Low Drift 4 Digit Display
Category:
Other Application Instruments
Features: ※ 30000 Counts Display ※ High Accuracy 0.05% ※ Hi/Lo Comparator and Limit Percent Setting ※ Measurement of REL, Actual and % Value ※ Continuous or Triggered Measurement Mode ※ Temperature Compensation and Measurement ※ Four-Terminal Measurement Technique ※ Auto-Recall Last Setting After Power OFF and ON Again ※ Alarm Setting for PASS/FAIL ※ Scan, Handler Interface(Standard) ※ Manual or Autoranging ※ RS-232C+GPIB (Option)