You have 0 items in your cart.
By Brands
Category:
Logic Analyzers
Features * 32/16 Input Channel * Time Analysis : Up to 200MHz Internal Sampling Rate * State Analysis : Up to 100MHz External Input Clock * Memory Depth : Up to 2Mbits/1Mbits (Half/Full Channels) * Enable Qualifier : High/Low Level Enable and Enable Delay Function * Signal Analyzer : I2C, RS-232C Protocol Analyzer and Signal Statistics * File Export : Signal Data, Operation Setting and Display Image * USB 2.0 Supported(1.1 Compatible)
Category:
Programmable AC / DC Power Source
Features : - 5.7" Large LCD Display- Output Capacity: 1kVA(for AC 200V Input)- Output Modes: AC and AC+DC Combined with any of four signal sources- Signal Source: Internal(INT),External(EXT),Internal+Externl(ADD)and Sychronization(SYNC)- Arbitrary Waveform Power Output- Power Amplifier of External Signal- Measurement Functions: Voltage, Current, Power ,Frequency, PowerFactor,CF,and Harmonic Current- Capacitor Input Load Supported- Sequence Function Allows Programming of Output Patterns- Limiter Function ( Upper / Lower / Limit Function)- 30 sets of Save / Recall Memory- Output On / Off Switch- USB(USBTMC)and RS-232 Standard for Remote Control- PC Software (Including Data Logging)
Category:
Smoke sensor
SD-50, the smoke detector with built-in micro processor, receiving signal from sensor and comparing it with preset alarming value, if it exceeds, transmits the relay output to be connected to PLC/DDC. Usually, the other smoke detectors designed only for fire alarm cannot be used for industrial use because it cannot secure enough accuracy and stability. However, SD-50 accommodating highest accurate ionization sensor and industrial detector technology, secures best accuracy and stability at the same time.
Category:
Analog Oscilloscopes
Features * 100MHz Bandwidth, Dual Channel, Delayed Sweep * Built-In 6 digits Universal Counter (GOS-6103C)* 10 Sets Memory for Front Panel Setting Save & Recall (GOS-6103/GOS-6103C)* Time Base Auto-range (GOS-6103/GOS-6103C)* Cursor Readout with 7 Measurements * Panel Setup Lock of Digital-Control Functions * Buzzer Alarm * LED Indicators * TV Synchronization
Category:
DDS Function Generators
Features *DDS Technique and FPGA Chip Design *Frequency Range : 0.1Hz~4/10MHz *High Frequency Accuracy : ± 20ppm *Frequency Resolution : 100mHz *Low Distortion Sine Wave : -55dBc,0.1Hz~200kHz *Front Panel Setting Save/Recall with 10 Groups of Setting Memories *Built-In 9 Digits,150MHz/High Resolution Counter(SFG-2110 Only)*INT/EXT AM/FM Modulation (SFG-2110 Only)*LIN/LOG Sweep Mode(SFG-2110 Only)
Category:
Programmable DC Electronic Load
Features : -Operating voltage (DC)：1.5V~150V-Operating Mode : C.C / C.V / C.R / C.P / CC+CV / CR+CV / CP+CV -Parallel Connection of Inputs for Higher Capacity (Max : 9,450W)-Support of High Slew Rate：Max 16A/us-Run Program Function（GO/NO GO Test）-Sequence Function for High Efficient Load Simulations-Commands are compatible with Kikusui PLZ-4W model.-Dynamic(Switching) Function：0.0166Hz ~20kHz-Soft Start Function：Off / On(1~200ms, Res：1ms)-Adjustable OCP / OVP / OPP / UVP Setting -Short Circuit Function-Timer function : Elapsed Time of load on -Cut Off Time(Auto Load Off Timer )：1s to 999h 59min 59s or Off -External Channel Control / Monitoring via Analog Control Connector-Setup Memories：100 sets-3.5 Inch TFT LCD Display-Multi Interface : USB 2.0 Device / Host , RS-232 , GPIB (Optional)
Category:
Indicator
DI-20 has built-in high performance A/D converter & micro-processor which enable multi input signals, output signal transmission, communication, and alarm
Category:
LCR Fixtures
Features: * 4 Wire* SMD/Chip components support* Suitable for SMD Range: 0201 to 0805* For LCR-8000G, LCR-800 Series