You have 0 items in your cart.
Accessories
Sub Categories
Category:
Interface Cables
MadgeTech’s IFC200 interface cable communicates between stand alone data loggers and the MadgeTech software. Through this interface, loggers can be started, stopped or downloaded. The IFC200 has been redesigned, and is now “plug and play”. It can be directly connected to a computer without installing any drivers and is compatible with Windows XP SP3, Windows Vista (32 and 64 bit), and Windows 7 (32 and 64 bit) operating systems. The improved IFC200 can now operate at up to 500 Volts RMS relative to the computer’s earth ground when attached. The IFC200 is equipped with communication LEDs, that provide a quick indication of the device status. The blue light illuminates when the device is plugged in and successfully recognized by Windows. The red light flashes when data is sent, and the green light flashes when data is received.
Category:
Current Switches/Transducers
Split core current relay switch, monitors 1.25-50Amps, adjustable set point between 1.25-50Amps, status LED's.
Category:
Enclosures
The Waterbox110C is a water resistant enclosure designed for use with the 110 series data loggers. This enclosure provides a water tight seal, allowing non-water resistant data loggers to be used in wet environments. The Waterbox110C is machined out of black anodized aluminum, and is wall mountable. The enclosure features a water-tight communication access plug and cable gland outlet. To use, simply unscrew the 4 hex screws and insert the data logger. Loosen the compression fitting and thread the sensor lead wire through the fitting. Attach the probe to the data logger and insert, then tighten the six screws again and it’s ready to use.
Category:
Probes
The pH-RUGGED ELECTRODE is a submersible CPVC pH electrode that is suited for use in outdoor applications such as monitoring drums, tanks or streams. The electrode has a quick latch mechanism which allows it to be inserted into a BNC connector by simply rotating it a quarter turn. For use with the MadgeTech pH loggers, a cable assembly and an RTD temperature reference is required. Two mounting assembly options are available. The pH RUGGED ATC CABLE mounting assembly connects directly to the pH-RUGGED ELECTRODE and has a built in RTD probe, providing automatic temperature compensation (ATC). The pH-RUGGED PROBE cable assembly connects to the pH-RUGGED ELECTRODE and can be used with an external RTD probe or may be used with one of the resistor kits included with the MadgeTech pH loggers. Automatic Temperature Compensation is preferred, as it provides the best accuracy. When the precision and accuracy of ATC is not necessary, use the included resistor kit to simulate the temperature of the application to minimize error. Compatible MadgeTech Data Loggers: pHTemp101, pHTemp2000, RFHTemp101A. Resistor Kit: Reference the table included with the resistor kit to calibrate the resistor...
Category:
O-Rings
One Set of Replacement O-Rings for PRTemp1000 Series (not available for Intrinsically Safe products).
Category:
Data Logger Batteries
3.6 Volt, Lithium Battery, 750 mAH. Note: These batteries are only equipped with two leads and the leads have been cut for use with MadgeTech data loggers.
Category:
Interface Cables
MadgeTech’s IFC202 interface cable communicates between the Micro series data loggers and the MadgeTech software. Through this interface, loggers can be started, stopped or downloaded. The IFC202 has been redesigned, and is now “plug and play”. It can be directly connected to a computer without installing any drivers and is compatible with Windows XP SP3, Windows Vista (32 and 64 bit), and Windows 7 (32 and 64 bit) operating systems. The improved IFC202 can now operate at up to 500 Volts RMS relative to the computer’s earth ground when attached. The IFC202 is equipped with communication LEDs, that provide a quick indication of the device status. The blue light illuminates when the device is plugged in and successfully recognized by Windows. The red light flashes when data is sent, and the green light flashes when data is received. The IFC202 is compatible with the MicroTemp, MicroRHTemp, EggTemp, EggTemp-RH and EGMS.